Parts

• Monitors filter system pressure in real time to signal when backwashing is needed and confirm the system is operating within safe parameters
• Standard 0-30 PSI range covers the full operating spectrum of above-ground pool sand filters
• Brass fitting and easy-to-read dial face built for continuous outdoor use

Specifications & documents

• SKU: 395-1014
• Shipping weight: 1.00 lb

• Same reliable half-clamp design as the black version, finished in light oak to match beige and tan filter housings
• Keeps the filter tank sealed securely at the mid-body seam to prevent leaks under operating pressure
• Direct replacement part for compatible Doughboy filter models

Specifications & documents

• SKU: 340-2183
• Shipping weight: 1.00 lb

• Complete replacement multiport valve with integrated basket extension for compatible above-ground pool filter systems
• Side-seal design ensures a pressure-tight connection between the valve body and tank to prevent bypass leaks
• Controls all filtration modes from a single valve point, restoring full filter functionality when the original valve fails

Specifications & documents

• SKU: 1107-2468
• Shipping weight: 1.00 lb

• Direct replacement handle restores easy manual control of the multiport valve without replacing the entire valve assembly
• Lever-style grip provides a firm, comfortable hold for switching between filter, backwash, rinse, and other modes
• Compatible with standard Doughboy multiport valve bodies

Specifications & documents

• SKU: 340-2228
• Shipping weight: 1.00 lb

• Fills the o-ring groove to maintain proper sealing geometry when the groove shows wear or distortion
• Prevents o-ring migration and bypass leaks that reduce filter efficiency over time
• Simple, low-cost fix that extends the service life of the valve body without full replacement

Specifications & documents

• SKU: 308-1282
• Shipping weight: 1.00 lb

• Replacement pin set secures the rotor in proper alignment inside the valve body
• Worn or broken pins cause the rotor to slip out of position, resulting in poor mode selection and bypass leaks
• Inexpensive hardware fix that restores precise valve operation without replacing the full rotor or valve

Specifications & documents

• SKU: 1121-1644
• Shipping weight: 1.00 lb

• Direct replacement impeller assembly restores full flow and pressure to 1½ HP PowerLine PPII pumps when the original shows wear, cracking, or reduced performance
• Precision-balanced design maintains efficient water movement and minimizes motor strain during continuous operation
• OEM-spec fit eliminates guesswork and ensures proper clearance inside the volute

Specifications & documents

• SKU: 1107-1547
• Shipping weight: 1.00 lb

• Mechanical shaft seal prevents water from migrating along the pump shaft into the motor, protecting against premature motor failure
• 5/8" sizing fits standard PowerLine pump shaft diameters — a common wear item that should be replaced any time the pump is opened for service
• Replacing a worn seal at first sign of leakage prevents significantly more costly motor damage

Specifications & documents

• SKU: 308-1263
• Shipping weight: 1.00 lb

• Companion spring to the mechanical pump seal maintains consistent pressure against the seal face to prevent shaft leakage
• Worn or collapsed springs allow the seal to lose contact and begin leaking — inexpensive replacement that restores a watertight shaft seal
• Should be replaced together with the pump seal during any seal service for reliable, long-lasting results

Specifications & documents

• SKU: 308-1264
• Shipping weight: 1.00 lb

• Replacement retaining nut secures the power switch in the pump housing for PowerLine PPI and PPII models
• Prevents switch movement and maintains proper electrical contact during pump operation
• Small but critical hardware component that keeps the switch assembly firmly seated and safely secured

Specifications & documents

• SKU: 303-1110
• Shipping weight: 1.00 lb

• Replacement handles make lifting the skimmer basket out of the housing quick and clean without reaching into the water
• Durable molded construction resists warping and breakage through repeated wet/dry cycles
• Direct fit for compatible Doughboy skimmer basket models

Specifications & documents

• SKU: 321-1002
• Shipping weight: 2.00 lb

6 reasons customers love this

• OEM-style replacement part/accessory intended to restore proper fit and function.
• Helps maintain dependable performance by replacing worn, damaged, or missing components.
• Built for pool-environment durability (water exposure, chemicals, outdoor conditions).
• Easier troubleshooting and ordering—use the SKU/UPC when contacting support or dealers.
• Supports proactive maintenance to reduce downtime during peak swim season.
• Use compatible manuals/parts lists to confirm fit for your exact model before installing.

Specifications & documents

• SKU: 1107-1356
• Shipping weight: 1.00 lb

• Complete replacement basket assembly for standard skimmers and PowerLine PP I pump models captures hair, lint, and fine debris before it reaches the impeller
• Full assembly replacement ensures all components fit and seal correctly together rather than mixing worn and new parts
• Compatible with standard Doughboy skimmer and PP I pump configurations

Specifications & documents

• SKU: 1300-1002
• Shipping weight: 1.00 lb

• Replacement gasket seals the return fitting where it passes through the pool wall, preventing leaks at one of the most common failure points
• U-shaped profile provides full circumferential sealing contact around the fitting opening
• Compatible with standard Doughboy above-ground pool return fittings

Specifications & documents

• SKU: 307-1031
• Shipping weight: 1.00 lb

• Replacement outer face plate in almond finish restores a clean, finished appearance to the pool wall skimmer opening
• Covers the wall cutout and secures the skimmer gasket assembly against the pool wall
• Almond color matches standard beige and tan above-ground pool wall finishes

Specifications & documents

• SKU: 340-1274
• Shipping weight: 1.00 lb

• Weighted replacement basket assembly sits firmly in the skimmer housing without floating or shifting during operation
• Integrated weight keeps the basket seated at the bottom of the housing for consistent debris capture even at high flow rates
• Complete assembly replacement ensures proper fit and function in compatible Doughboy skimmer models

Specifications & documents

• SKU: 1121-1075
• Shipping weight: 2.00 lb